General Electric was born from Thomas Edison's electric companies merging with the Thomson-Houston Electric Company. Wire in and switch on the ekrPro Com60 controller as stipulated in the operating manual. Slide the sensor along in the sensing roller direction until the protective packaging lies up against the sensing roller see drawing. Detailed descriptions can be found in Section 5. Securing screws Dont crush or clamp the cable! Hamilton Swapped cameras cables and surprisingly neither unit worked then. The current setting is displayed in the System info sub-menu as Commander Node see Section 5.
Opening the menu will only be displayed once. Maintenance and cleaning work must only be undertaken on the sensor and the control panel after the power supply has been switched off. The number of blocking actions undertaken will be kept to a minimum in this case. Head over to our and let us know. Use the mechanical adjustment device to fix it in position.
A selection list of saved jobs will be displayed. The firmware will be automatically loaded into the system during this time. Cover or shield any adjacent parts that are still live. Sensor with control panel removed The length of the connection cable between the sensor and the control panel must never exceed 20 m maximum. The display will change over from set-up mode to scanning mode. The connection sizes can be found in the following drawing. Setting the device address: 1.
If you are unable to enter any of these settings for your application you can use the relevant settings to create your own jobs. Mode switch of the camera is set to 5, which is to detect center position between 2 edges. The controller compares the actual recorded position against the default set point position. The measuring windows protective lens cover must be cleaned regularly in order to obtain optimum guiding results. A blue background will now be displayed around the window. The structure is a hierarchal structure see menu structure in Section 4.
Only the guiding unlock and guiding lock settings are available for these parameters at the moment. For details, see the actual locations in this manual. This will ensure that a minimum control time is run when scanning a broken line and that the guiding device can react. Unscrew the stopper in the sensor enclosure 3. Whether the terminator resistor has been set up Resistor There must always be one sensor and one panel with corresponding nodes present on the bus e.
The search area will be only be opened if web movement has been detected or if an edge cannot be found. Protecting against the voltage being switched back on 3. The operator must be able to access the control panel easily. The parameters are user organized, i. Current operating mode controller Status bar Shows you which modes the sensor and the controller are working in. The current mode will be displayed in the top right of the screen.
The procedure is given in Section 5. Assignments have already been set-up in the factory see factory default settings. If the arrow key is kept held down for longer than the time defined in the time to increase step width parameter it will switch over to the adjustment step width defined in the fast step width of guiding position parameter. Panel firmware can be recognised by the C in the file name. Any part found to be working incorrectly must be replaced immediately. This must remain stabile over the measuring process.
Pull the control panel out of the control panel enclosure Now pull the connecting cable and the plug carefully through the cut-out in the controller enclosure. The set point position will be indicated by a white triangle displayed on the control panels screen. In this case the connection between the sensor and control panel is completed using a cable extension that is available as an optional extra. This shows you how the optimization can be run in the displayed window. Select the Change User sub-menu from the main menu and then log on as Administrator.
Proceed as follows to make an entry in the footnote: The positions that have to be changed will flash. You are only allowed to open the sensor if the power supply has been switched off! A blue background will now be displayed around the window the sensor lighting flashes and the laser is switched on. Unscrew the four control panel securing screws. Use the four securing screws to attach the control panel to the sensor. These settings can also be used for weak colors inside a light background.
Use the optional extension cable to connect up the control panel to the sensor see Chapter 2. The display will change over from set-up mode to scanning mode. You can select from 4 different mounting positions in principle, but mounting position A is the standard setting and mounting positions B D are optional and these must be activated before you can use them. The Hotel Software used for been tested by Softonic, but provide tech support for their. The following selection window will be displayed. You can now adapt the parameters that can be accessed from this level. Select sensor and then open the setting up window.